Latest [Apr 05, 2022] NACE-CIP1-001 Exam Dumps - Valid and Updated Dumps
Free Sales Ending Soon - 100% Valid NACE-CIP1-001 Exam Dumps with 100 Questions
Do you know about the need for the NACE CIP1-001 exam?
There are different kinds of certifications that can help candidates to achieve a good career. The NACE CIP1-001 exam is one of them. It allows the candidates to get a certification as a certified coatings inspector. There are different types of NACE CIP1-001 exams available. You can choose any of them. You should not waste your time by choosing any wrong exam. We are giving you all the information about the NACE CIP1-001 exam. Choose a suitable exam for you. A credit card can be used to purchase any product or service. You can use it to pay for the NACE CIP1-001 exam dumps. A prospective employer can easily find a suitable candidate through these materials. Our products are very helpful in the preparation for this exam. It is the best material that you can use to pass this exam easily. Permitted to transport is the most important issue for any business. Abrasive is a type of powder used in various industries. It is also called abrasive dust. The purpose of using this powder is to remove the unwanted layers from any surface. It is used in many types of industries such as steel, power, mining, and construction. In this process, abrasive can be harmful to people. There are different types of abrasive available. They include fine, coarse, superfine, and ultrafine.
NEW QUESTION 32
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Document the problem and advise the Contractor and Owner's representative
- B. Document the problem and advise the Contractor
- C. Break the blisters to see what's inside
- D. Extract any liquid that may be inside the blister and send it to the lab for further analysis
Answer: A
NEW QUESTION 33
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Record the segment with the more aggressive profile
- B. Record your result by identifying two segments
- C. Use another method as the comparator method is too subjective
- D. Record the segment with the less aggressive profile
Answer: D
NEW QUESTION 34
Upon arrival of coating materials, the inspector should
- A. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- B. observe and document time frame and environmental conditions between each coat.
- C. observe aryl document that the applicator WFT at regular intervals during application.
- D. observe and document the amount of material and batch numbers.
Answer: D
NEW QUESTION 35
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Ultra-Violet light may contaminant the surface
- B. Presence of weld spatter may produce a false positive
- C. Synthetic oil or grease may not be identified
- D. Chloride salt may produce a false positive
Answer: C
NEW QUESTION 36
Relative humidity is
- A. the lowest temperature at which moisture forms on a steel surface.
- B. a measure of the amount of moisture in the air compared to saturation level.
- C. a measure of the amount of moisture in the air compared to the air temperature.
- D. the highest temperature at which moisture forms on a steel surface.
Answer: B
NEW QUESTION 37
ISO SA 3 is directly equivalent to:
- A. None of the above
- B. NACE No. 3/SSPC SP 6
- C. NACE No. 2/SSPC SP 10
- D. NACE No. 1/SSPC SP 5
Answer: A
NEW QUESTION 38
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Shut the job down
- C. Review the relevant standard with the Contractor
- D. Permit coating to take place so as not to lose the blast
Answer: C
NEW QUESTION 39
Which one of the following documents is the best source for coating technical data:
- A. Technical Data Sheet
- B. Safety Data Sheet;
- C. Application Guidelines
- D. Specification
Answer: A
NEW QUESTION 40
Stripe coats are best applied by:
- A. High volume low pressure spray
- B. Conventional spray
- C. Brush
- D. Airless spray
Answer: C
NEW QUESTION 41
The most important factor resulting in improved job site safety is:
- A. Situational Awareness
- B. Safety Enforcement
- C. Engineering Controls
- D. Personal Protective Equipment
Answer: A
NEW QUESTION 42
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. High Relative Humidity
- B. High Surface Temperature
- C. Low Surface Temperature
- D. Low Relative Humidity
Answer: D
NEW QUESTION 43
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Surface Condition H
- B. Surface Conditions E-G
- C. Rust Grades A-D
- D. Rust Grades 1-4
Answer: C
NEW QUESTION 44
Digital hygrometers
- A. are used to measure temperature from a distance.
- B. use a thermocouple in contact with the surface to measure temperature
- C. consist of a bimetallic sensing element protected from wind gusts.
- D. determine relative humidity, air temperature, and dew point temperature:
Answer: D
NEW QUESTION 45
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Check the credentials of the Safety Officer on site
- B. Act in accordance with the site safety requirements and set an example
- C. Check the PPE used by the Applicators
- D. Assume the role of the Safety Inspector
Answer: B
NEW QUESTION 46
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Call your supervisor
- B. Advise the Contractor of your readings
- C. Advise the Contractor he cannot proceed
- D. Advise the Contractor he can proceed
Answer: B
NEW QUESTION 47
What is used to determine compressed air cleanliness?
- A. Psychrometer
- B. Profilometer
- C. Needle pressure gauge
- D. Blotter test
Answer: B
NEW QUESTION 48
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Achieve consensus through negotiation
- B. Call the supervisor
- C. Go with the majority opinion
- D. Never change his/her mind
Answer: B
NEW QUESTION 49
NACE SP 0178 is a standard for:
- A. Tanks and Vessels to be Externally Coated
- B. Stainless steel pipe to be Externally Coated
- C. Structural steel to be coated for Atmospheric Service
- D. Tanks and Vessels to, be Lined for Immersion Service
Answer: D
NEW QUESTION 50
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Default to the owner's Inspection and Test Plan
- B. Bring the matter up at the pre-job conference
- C. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
- D. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
Answer: B
NEW QUESTION 51
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
- B. Advise the owners' representative of your lack of knowledge in this area
- C. Carefully review the document and do the best you can
- D. Hire a third patty to assist you in understanding the document
Answer: C
NEW QUESTION 52
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 70% of the specified maximum thickness
- B. 100% of the specified maximum thickness
- C. 80% of the specified minimum thickness
- D. 90% of the specified maximum thickness
Answer: C
NEW QUESTION 53
......
NACE-CIP1-001 Exam Dumps - 100% Marks In NACE-CIP1-001 Exam: https://dumpstorrent.prep4surereview.com/NACE-CIP1-001-latest-braindumps.html
